Description:

Product name: 8/10-port SATA3.0 expansion card

Product model: PCE8SAT-M01

Product master: Marvell 88SE92xx+JMB5XX

Product packaging: cowhide box

Product interface: PCI-E 1X 2X 4X 8X 16X

Support system: WINXP WIN7 WIN8 WIN10, Ubuntu

Product specifications:

Comply with Serial ATA 3.0 specification, backward compatible with SATA2.0 SATA1.0

Comply with PCI-Express v2.0 specification and backward compatible with PCI-Express v1.0.

Support 6.0 Gbps, 3.0 Gbps and 1.5 Gbps of communication speed

Supports Gen 1i, Gen 1x, Gen 2i, Gen 2m, Gen 2x, and Gen 3i.

Support AHCI1.0 mode and IDE mode

Support native command queue (NCQ)

Support FIS based on port multiplier switch or command switch.

Support hot swap and hot swap.

Compatible with SATA6G, 3G and 1.5G hard drives

Bus interface: PCI-Express x1 slot

Expansion interface: 8/10 SATA3.0 interfaces

System requirements: There is an available PCI Express X1 slot, while supporting PCI-E X2 X4 X8 X16

Operating system: Windows10/8/7 (32/64 bit)/ Vista (32/64 bit)/ XP/2003/2008/linux

Packing accessories: expansion card*1 CD*1 baffle*1

About speed description:

1. The best effect can be achieved with SATA3.0 data cable

2. PCI-E must have a slot above V2.0. For V1.0, the speed will not exceed 250M. Whether PCI-E is X1 or X16, as long as it is V2.0 version, it can be inserted directly if there is a spare X16 slot. On the X16 slot,

3. The setting of motherboard BOIS: SATA mode should be changed to AHCI. Although some motherboards PCIE is version 2.0, BOIS does not enable high-speed transmission mode by default (gen2 high speed mode), which needs to be manually enabled. Under PCI-E 1.0, only 200- 250M, 2.0 is below 350-400M, if you don't accept it, change the motherboard.

4. SATA ports will slow down when they are used at the same time, which is not suitable for users who are looking for speed. They are only used for expansion hard disk interfaces.

Product driver files:

1. CD:DRIVER\SATA CARD\Marvell\91XX_92XX Setup, then select the corresponding folder according to the system

The usage method of PCIE to SATA3.0 adapter card is as follows:

1. Connection conditions and solutions between system disk and PCIE to SATA3.0 adapter card:

1. The SATA interface mode of PCIE to SATA3.0 is AHCI mode. If you want to insert a system disk on our card, the premise is that your system disk must be installed in AHCI mode when installing the system on the motherboard, otherwise it will not pass. Our card adapter card starts the system.

2. If it is determined that the system disk is inserted into the SATA interface on the motherboard to install the system in AHCI mode, then you can directly insert the hard disk into our card, and then enter the motherboard BIOS to set the system disk as the first boot.

3. If both of the above conditions are met, if it still fails to boot or restarts repeatedly, then the motherboard's hard disk interface may conflict with our adapter card. The solution is to enter the motherboard BIOS and set the motherboard's hard disk interface option to Disabled, save and restart to start the system

2. Connection conditions and solutions for ordinary disks and PCIE to SATA3.0:

1. When the system disk is inserted on the motherboard and the ordinary disk is inserted on the PCIE to SATA3.0 card, then it is only necessary to detect the adapter card information and the ordinary disk model during startup.

2. If the condition 1 is established, the system still cannot be started, then enter the motherboard BIOS and set the system disk as the first startup.

3. Connection between system disk and ordinary disk and PCIE to SATA3.0 and solutions:

1. Prerequisite, if the system with the original motherboard installed on the system disk is an AHCI model test, the following methods can be used to achieve it. If the system is installed in IDE mode, then the system can only be reinstalled through PCIE to SATA3.0. .

2. After 1 condition is established, if you cannot boot, you need to enter the motherboard BIOS and set the first system disk as the first boot.

3. If all the conditions in 1.2 are met, it still cannot start, then the integrated SATA interface may conflict. Please enter the motherboard BIOS and set SATA to Disabled.